Revoked by MEPC.395(82)
RESOLUTION MEPC.346(78)
(adopted on 10 June 2022)
2022 GUIDELINES FOR THE DEVELOPMENT OF A SHIP ENERGY EFFICIENCY
MANAGEMENT PLAN (SEEMP)
THE MARINE ENVIRONMENT PROTECTION COMMITTEE,
RECALLING Article 38(a) of the Convention on the International
Maritime Organization concerning the functions of the Marine Environment
Protection Committee (the Committee) conferred upon it by international
conventions for the prevention and control of marine pollution from ships,
NOTING that the Committee, at its seventy-sixth session, adopted,
by resolution MEPC.328(76),
the 2021 revised MARPOL Annex VI, which will enter into force on 1 November
2022,
NOTING IN PARTICULAR that the 2021 revised MARPOL Annex VI (MARPOL
Annex VI) contains amendments concerning mandatory goal-based technical and
operational measures to reduce the carbon intensity of international shipping,
NOTING FURTHER that regulation 26 of MARPOL Annex VI requires each
ship to keep on board a Ship Energy Efficiency Management Plan (SEEMP), to be
developed and reviewed, taking into account the guidelines adopted by the
Organization,
RECOGNIZING that the aforementioned amendments to MARPOL Annex VI
require relevant guidelines for uniform and effective implementation of the
regulations and to provide sufficient lead time for industry to prepare,
NOTING that the Committee, at its seventieth session, adopted, by
resolution MEPC.282(70),
the 2016 Guidelines for the development of a Ship Energy Efficiency
Management Plan (SEEMP),
HAVING CONSIDERED, at its seventy-eighth session, the draft 2022
Guidelines for the development of a Ship Energy Efficiency Management Plan
(SEEMP),
1 ADOPTS the 2022
Guidelines for the development of a Ship Energy Efficiency Management Plan
(SEEMP), as set out in the annex to the present resolution;
2 INVITES
Administrations to take the annexed Guidelines into account when developing and
enacting national laws which give force to and implement requirements set forth
in regulation 26 of MARPOL Annex VI;
3 REQUESTS the
Parties to MARPOL Annex VI and other Member Governments to bring the annexed
Guidelines to the attention of masters, seafarers, shipowners, ship operators
and any other interested parties;
4 AGREES to keep the
Guidelines under review in light of experience gained with their
implementation, also taking into consideration that in accordance with
regulations 25.3 and 28.11 of MARPOL Annex VI a review of the technical and
operational measures to reduce the carbon intensity of international shipping
shall be completed by 1 January 2026;
5 REVOKES the 2016
Guidelines for the development of a Ship Energy Efficiency Management Plan
(SEEMP) adopted by resolution MEPC.282(70).
2022 GUIDELINES FOR THE DEVELOPMENT OF A SHIP ENERGY EFFICIENCY
MANAGEMENT PLAN (SEEMP)
CONTENTS
1 INTRODUCTION
2 DEFINITIONS
PART I OF THE SEEMP: SHIP MANAGEMENT PLAN TO IMPROVE ENERGY
EFFICIENCY
3 GENERAL
4 FRAMEWORK AND
STRUCTURE OF PART I OF THE SEEMP
5 GUIDANCE ON BEST
PRACTICES FOR FUEL EFFICIENT OPERATION OF SHIPS
PART II OF THE SEEMP: SHIP FUEL OIL CONSUMPTION DATA COLLECTION
PLAN
6 GENERAL
7 GUIDANCE ON
METHODOLOGY FOR COLLECTING DATA ON FUEL OIL CONSUMPTION, DISTANCE TRAVELLED AND
HOURS UNDER WAY
8 DIRECT CO2
MEASUREMENT
PART III OF THE SEEMP: SHIP OPERATIONAL CARBON INTENSITY PLAN
9 GENERAL
10 ATTAINED ANNUAL
OPERATIONAL CII CALCULATION METHODOLOGY; DATA COLLECTION PLAN AND DATA QUALITY
11 REQUIRED ANNUAL
OPERATIONAL CII FOR NEXT THREE YEARS
12 THREE-YEAR
IMPLEMENTATION PLAN
13 PROCESS FOR
SELF-EVALUATION AND IMPROVEMENT
14 REVIEW AND UPDATE
OF PART III OF THE SEEMP
15 PLAN OF CORRECTIVE
ACTIONS
APPENDIX 1 - SAMPLE FORM
OF SHIP MANAGEMENT PLAN TO IMPROVE ENERGY EFFICIENCY (PART I OF THE SEEMP)
APPENDIX 2 - SAMPLE FORM
OF SHIP FUEL OIL CONSUMPTION DATA COLLECTION PLAN (PART II OF THE SEEMP)
APPENDIX 2bis - SAMPLE FORM OF SHIP OPERATIONAL
CARBON INTENSITY PLAN (PART III OF THE SEEMP)
APPENDIX 3 - STANDARDIZED
DATA REPORTING FORMAT FOR THE DATA COLLECTION SYSTEM AND OPERATIONAL CARBON
INTENSITY TO THE ADMINISTRATION
APPENDIX 4 - STANDARDIZED
DATA REPORTING FORMAT FOR THE PARAMETERS TO CALCULATE THE TRIAL CARBON
INTENSITY INDICATORS ON A VOLUNTARY BASIS
1 INTRODUCTION
1.1 The Guidelines
for the development of a Ship Energy Efficiency Management Plan have
been developed to assist with the preparation of the Ship Energy Efficiency
Management Plan (SEEMP) required by regulation 26 of MARPOL Annex VI.
1.2 Taken together, the
aims of the SEEMP should assist the international shipping sector to achieve
the goal of Chapter 4 of MARPOL Annex VI set out in regulation 20, which is
reducing the carbon intensity of international shipping. The aims of the SEEMP
are threefold:
1.2.1 To encourage
companies to incorporate actions to improve the energy efficiency and carbon
intensity of their ships and ship management practices.
1.2.2 To specify the
methodology the ship should use to collect the data required by regulation 27.1
of MARPOL Annex VI and the processes that should be used to report the data to
the ship's Administration or any organization duly authorized by it.
1.2.3 To specify the
methodology the ship should use to calculate the attained annual operational
carbon intensity indicator (CII) as required by regulation 28.1 of MARPOL Annex
VI and the processes that should be used to report the data to the ship's
Administration or any organization duly authorized by it.
1.3 There are three
parts to a SEEMP:
1.3.1 Guidance for Part I
of the SEEMP required by regulation 26.1 of MARPOL Annex VI, is addressed in
sections 3, 4, and 5 of these Guidelines. The purpose of this part is to
provide an approach to monitor ship and fleet efficiency performance over time
and describe ways to improve the ship's energy efficiency performance and
carbon intensity. Part I of the SEEMP applies to any ship of 400 GT and above.
1.3.2 Guidance for part II
of the SEEMP required by regulation 26.2 of MARPOL Annex VI, is addressed in
sections 6, 7, and 8 of these Guidelines. The purpose of this part is to
provide a description of the methodologies that should be used to collect the
data required pursuant to regulation 27 of MARPOL Annex VI and the processes
that the ship should use to report the data to the ship's Administration or any
organization duly authorized by it. Part II of the SEEMP applies to any ship of
5,000 GT and above.
1.3.3 Guidance for part
III of the SEEMP required by regulations 26.3 and 28.8 of MARPOL Annex VI is
addressed in sections 9, 10, 11, 12, 13, 14 and 15 of these Guidelines. The
purpose of this part is to provide:
.1 a description of the methodology that
should be used to calculate the ship's attained annual operational CII required
by regulation 28 of MARPOL Annex VI;
.2 the processes that should be used to
report this value to the ship's Administration or any organization duly
authorized by it;
.3 the required annual operational CII for
the next three years;
.4 an implementation plan documenting how the
required annual operational CII should be achieved during the next three years;
.5 a procedure for self-evaluation and
improvement; and
.6 for ships rated as D for three consecutive
years or rated as E, a plan of corrective actions to achieve the required
annual operational CII.
1.3.4 Part III of the
SEEMP applies to any ship of 5,000 GT and above which falls into one or more of
the categories in regulations 2.2.5, 2.2.7, 2.2.9, 2.2.11, 2.2.14 to 2.2.16,
2.2.22, and 2.2.26 to 2.2.29 of MARPOL Annex VI.
1.3.5 Sample forms of the
various sections of the SEEMP are presented in appendices 1, 2, and 2bis
for illustrative purposes. A standardized data-reporting format for the data
collection system and operational carbon intensity is presented in appendix 3.
A standardized data reporting format for the trial carbon intensity indicators
on voluntary basis is presented in appendix 4.
2 DEFINITIONS
2.1 For the purpose of
these Guidelines, the definitions in MARPOL Annex VI apply.
2.2 "Ship fuel oil
consumption data" means the data required to be collected on an annual
basis and reported as specified in appendix IX to MARPOL Annex VI.
2.3 "Safety
management system" means a structured and documented system enabling
company personnel to implement effectively the company safety and environmental
protection policy, as defined in paragraph 1.1 of International Safety
Management Code.
2.4 "Carbon
Intensity Indicator" means a performance indicator by which it is possible
to measure the carbon intensity of the ship, as defined in the guidelines
developed by the Organization,1 taking into account data listed for
reporting in appendix IX to MARPOL Annex VI.
_________________
1 Refer to the 2021
Guidelines on operational carbon intensity indicators and the calculation
methods (CII guidelines, G1) (Resolution MEPC.336(76)) and the 2022 Guidelines on
correction factors and voyage adjustments for CII calculations (G5)
(Resolution MEPC.XXX(78)).
PART I OF THE SEEMP: SHIP MANAGEMENT PLAN TO IMPROVE ENERGY
EFFICIENCY
3 GENERAL
3.1 Regulation 26.1 of
MARPOL Annex VI requires each ship of 400 gross tonnage and above, subject to
chapter 4 to keep on board a ship-specific Ship Energy Efficiency Management
Plan (SEEMP).
3.2 The purpose of part
I of the SEEMP is to establish a mechanism for a company and/or a ship to
improve the energy efficiency and reduce the carbon intensity of a ship's
operation. Preferably, this aspect of the ship-specific SEEMP is linked to a
broader corporate energy management policy for the company that owns, operates
or controls the ship, recognizing that no two shipping companies are the same,
and that ships operate under a wide range of different conditions.
3.3 Many companies will
already have an environmental management system (EMS) in place under ISO 14001
which contains procedures for selecting the best measures for particular ships
and then setting objectives for the measurement of relevant parameters, along
with relevant control and feedback features. Monitoring of operational
environmental efficiency should therefore be treated as an integral element of
broader company management systems.
3.4 In addition, many
companies already develop, implement and maintain a safety management system.
In such case, part I of SEEMP may form part of the ship's safety management
system.
3.5 This section
provides guidance for the development of part I of SEEMP that should be
adjusted to the characteristics and needs of individual companies and ships.
Part I of the SEEMP is intended to be a management tool to assist a company in
managing the ongoing environmental performance of its ships and, as such, it is
recommended that a company develop procedures for implementing the plan in a
manner which limits any onboard administrative burden to the minimum necessary.
3.6 Part I of the SEEMP
should be developed as a ship-specific plan by the company, and should reflect
efforts to improve the energy efficiency and reduce carbon intensity of a ship
through four steps: planning, implementation, monitoring, and self-evaluation
and improvement. These components play a critical role in the continuous cycle
to improve ship energy efficiency management and reduce its carbon intensity.
With each iteration of the cycle, some elements of part I will necessarily
change while others may remain as before.
3.7 At all times safety
considerations should be paramount. The trade a ship is engaged in may
determine the feasibility of the energy efficiency and carbon intensity
reduction measures under consideration. For example, ships that perform
services at sea (pipe laying, seismic survey, OSVs, dredgers, etc.) may choose
different methods of improving energy efficiency when compared to conventional
cargo carriers. The nature of operations and influence of prevailing weather
conditions, tides and currents combined with the necessity of maintaining safe
operations may require adjustment of general procedures to maintain the
efficiency of the operation, for example the ships which are dynamically
positioned. The length of a voyage and the need to avoid high risk areas may
also be important parameters as well as trade specific safety considerations.
4 FRAMEWORK AND
STRUCTURE OF PART I OF THE SEEMP
4.1 Planning
4.1.1 Planning is the most
crucial stage of part I of the SEEMP, in that it primarily determines both the
current status of ship energy usage and carbon intensity and the expected
improvement of ship energy efficiency and reduction of carbon intensity.
Therefore, it is encouraged to devote sufficient time to planning so that the
most appropriate, effective and implementable plan can be developed.
Ship-specific measures
4.1.2 Recognizing that
there are a variety of options to improve energy efficiency and reduce carbon
intensity (e.g. speed optimization, confirming berth availability and arrival
time with port of destination, weather routeing, hull maintenance, retrofitting
of energy efficiency devices, and use of alternative fuels), the best package
of measures for a ship to improve energy efficiency and reduce carbon intensity
depends to a great extent upon ship type, cargoes, routes and other factors
that should be identified in the first place. These measures should be listed
as a package of measures to be implemented, thus providing the overview of the
actions to be taken for that ship.
4.1.3 During the planning
process, therefore, it is important to determine and understand the ship's
current status of energy usage. Part I of the SEEMP should identify
energy-saving and carbon intensity reducing measures that already have been
undertaken, and should determine how effective these measures are in terms of
improving energy efficiency and reducing carbon intensity. Part I also should
identify what measures can be adopted to further improve the energy efficiency
and reduce the carbon intensity of the ship. It should be noted, however, that
not all measures can be applied to all ships, or even to the same ship under
different operating conditions and that some of them are mutually exclusive.
Ideally, initial measures could yield energy (and cost) saving results that
then can be reinvested in more difficult or expensive efficiency upgrades
identified by part I.
4.1.4 Guidance on best
practices for fuel-efficient operation of ships, set out in chapter 5, can be
used to facilitate this part of the planning phase. Also, in the planning
process, particular consideration should be given to minimize any onboard
administrative burden.
Company-specific measures
4.1.5 The improvement of
energy efficiency and reduction of carbon intensity of ship operation does not
necessarily depend on single ship management only. Rather, it may depend on
many stakeholders including ship repair yards, shipowners, operators,
charterers, cargo owners, fuel suppliers, ports and traffic management
services. For example, "just in time" - as explained in paragraph
5.2.4 - requires good early communication among operators, ports and traffic
management services. The better the coordination among such stakeholders, the
more improvement can be expected. In most cases, such coordination or total
management is better made by a company rather than by a ship. In this sense, it
is recommended that a company should also establish an energy efficiency and
carbon intensity management plan to improve the performance of its fleet
(should it not have one in place already) and make necessary coordination among
stakeholders.
Human resource development
4.1.6 For effective and
steady implementation of the adopted measures, raising awareness of and
providing necessary training for personnel both on shore and on board are an
important element. Such human resource development is encouraged and should be
considered as an important component of planning as well as a critical element
of implementation.
Goal setting
4.1.7 The last part of
planning is goal setting.
.1 For ships also subject to regulation 28 of
MARPOL Annex VI, the goal setting should be consistent with the continuous CII
improvements set out by that regulation, and should include the relevant
information (see paragraph 9.7). These ships are also encouraged to consider
setting ship-specific goals in addition to the applicable CII requirements that
strive for additional energy efficiency improvements and carbon intensity
reductions.
.2 For ships or
companies not subject to regulation 28, there are no requirements to define a
goal and to communicate it to the public, or to be a subject to external
inspection, surveys, or audits with respect to the SEEMP. Nevertheless, a
meaningful goal should be defined to serve as a signal on a company's
commitment to improve the energy efficiency and carbon intensity of the ship.
The goal can be set using different indicators, including the annual fuel
consumption, Annual Efficiency Ratio (AER), cgDIST, Energy Efficiency
Operational Indicator (EEOI) or other carbon intensity indicators (CIIs).2
In all cases, the goal should be measurable and easy to understand.
________________
2 Refer to the 2022
Guidelines on operational carbon intensity indicators and the calculation
methods (CII guidelines, G1) (Resolution MEPC.352(78)) and the 2022 Interim
guidelines on correction factors and voyage adjustments for CII calculations
(G5) (Resolution MEPC.355(78)).
4.2 Implementation
Establishment of implementation system
4.2.1 After a ship and a
company identify the energy efficiency and carbon intensity measures to be
implemented, it is essential to establish a system for their implementation.
This is done by developing the procedures for energy management, defining tasks
associated with those procedures, and assigning those tasks to responsible
personnel. The implementation system should include procedures to ensure
execution of measures and specify defined levels of authority and lines of communication.
Also, it should include procedures for internal audits and management review,
where relevant. In sum, part I of the SEEMP should describe how each measure
should be implemented and who the responsible person or persons are. The
implementation period (start and end dates) of each selected measure should be
indicated. The development of such an implementation system can be considered
as a part of planning, and therefore may be completed at the planning stage.
Implementation and record-keeping
4.2.2 The planned measures
should be carried out in accordance with the predetermined implementation
system. Record-keeping for the implementation of each measure is beneficial for
self-evaluation at a later stage and should be encouraged. If any identified
measure cannot be implemented for any reason, the reason or reasons should be
recorded for internal use. It is recommended that events and operational
conditions outside the control of the ship's crew (for example, waiting for
berths, extended port dwell times, operation in severe adverse weather) which
may affect the ships rating be documented.
4.3 Monitoring
Monitoring tools
4.3.1 The energy
efficiency of a ship should be monitored quantitatively. This should be done by
an established method, preferably by an international standard. In many cases,
the monitoring tool should target the goal indicator set out in paragraph 4.1.7
(e.g. AER, cgDIST, EEOI, or other CIIs as agreed by the Organization). If a
quantitative goal is not defined for a ship, a quantitative performance
indicator developed by the Organization (e.g. AER, EEOI, CII) or another
internationally established tool should be selected. A ship subject to
regulation 28 is likely to use the CII as its monitoring tool.
4.3.2 If used, these CIIs
should be calculated in accordance with the guidelines developed by the
Organization,3 adjusted, as necessary, to a specific ship and trade.
________________
3 Refer to the Guidelines
for voluntary use of the ship energy efficiency operational indicator (EEOI)
(MEPC.1/Circ.684)
and the 2022 Guidelines on operational carbon intensity indicators and the
calculation methods (CII guidelines, G1) (Resolution MEPC.352(78))
and the 2022 Interim guidelines on correction factors and voyage adjustments
for CII calculations (G5) (Resolution MEPC.355(78)).
4.3.3 Ships subject to
regulation 28 may use other measurement tools in addition to the CII, if convenient
and/or beneficial for a ship or a company. In the case where other monitoring
tools are used, the reason for the use of the tool and the method of monitoring
should be clarified at the planning stage.
4.3.4 It is highly advised
to conduct monitoring at regular intervals for checking consistency of data and
verification assistance. The ship's fuel oil consumption should be monitored
using daily reporting, such as noon reports, or higher frequency data.
Establishment of monitoring system
4.3.5 It should be noted
that whatever measurement tools are used, continuous and consistent and
reliable data collection is the foundation of monitoring. To allow for
meaningful and consistent monitoring, a monitoring system, including the
procedures for collecting data and the assignment of responsible personnel,
should be developed. The development of such a system can be considered as a
part of planning, and therefore should be completed at the planning stage.
4.3.6 It should be noted
that, in order to avoid unnecessary administrative burdens on ships' staff,
monitoring should be carried out as much as possible by shore staff when the
data can be automatically transferred, utilizing data obtained from existing
required records such as the official and engineering logbooks and oil record
books. Additional data could be obtained as appropriate.
Search and rescue
4.3.7 When a ship diverts
from its scheduled passage to engage in search and rescue operations, and for
which emissions are excluded pursuant to regulation 3, it is recommended that
data obtained during such operations is not used in ship energy efficiency
monitoring, and that such data should be recorded separately.
4.4 Self-evaluation and
improvement
4.4.1 Self-evaluation and
improvement is the final phase of the management cycle. This phase should
produce meaningful feedback for the coming first stage, i.e. planning stage of
the next improvement cycle.
4.4.2 The purpose of
self-evaluation is to:
.1 evaluate the effectiveness of the planned
measures and their implementation;
.2 deepen the understanding of the overall
characteristics of the ship's operation such as what types of measures can or
cannot function effectively, and how and/or why;
.3 comprehend the trend of the efficiency
improvement of that ship; and
.4 develop the improved management plan for
the next cycle through identification of further opportunities for improving
energy efficiency and reducing carbon intensity.
4.4.3 For this process,
procedures for self-evaluation of the ship energy efficiency management plan
should be developed. Furthermore, self-evaluation should be implemented
periodically by using data collected through monitoring. In addition, it is
recommended that time be invested in identifying the cause and effect of the
performance during the evaluated period so lessons learned can be taken into
account when revising and improving the next stage of the ship's energy
efficiency management plan.
5 GUIDANCE ON BEST
PRACTICES FOR FUEL-EFFICIENT OPERATION OF SHIPS
5.1 The search for
energy efficiency and carbon intensity improvement across the entire transport
chain takes responsibility beyond what can be delivered by the company alone. A
list of all the possible stakeholders in the efficiency of a single voyage is
long: obvious parties are designers, shipyards and engine manufacturers for the
characteristics of the ship; and charterers, fuel suppliers, ports and vessel
traffic management services, etc. for the specific voyage. All parties involved
should consider the inclusion of efficiency measures in their operations both
individually and collectively.
5.2 Fuel-efficient
operations
Improved voyage planning
5.2.1 The optimum route
and improved efficiency can be achieved through the careful planning and
execution of voyages. Thorough voyage planning needs time, but a number of
software tools are available to assist in voyage planning.
5.2.2 The Guidelines
for voyage planning, adopted by resolution A.893(21), provide essential guidance for the
ship's crew and voyage planners.
Weather routeing
5.2.3 Weather routeing has
a high potential for efficiency savings on specific routes. It is commercially
available for all types of ship and for many trade areas.
Just in time
5.2.4 Good early
communication with the next port should be an aim in order to give maximum
notice of berth availability and facilitate the use of optimum speed where port
operational procedures support this approach.
5.2.5 Optimized port
operation could involve a change in procedures involving different ship
handling arrangements in ports. Port authorities should be encouraged to
maximize efficiency and minimize delay.
Speed optimization
5.2.6 Speed optimization
can produce significant savings. However, optimum speed means the speed at
which the fuel used per tonne mile is at a minimum level for that voyage. It
does not mean minimum speed; in fact, sailing at less than optimum speed will
consume more fuel rather than less. Reference should be made to the engine
manufacturer's power/consumption curve and the ship's propeller curve. Possible
adverse consequences of slow speed operation may include increased vibration
and problems with soot deposits in combustion chambers and exhaust systems.
These possible consequences should be taken into account. For LNG carriers
speed optimization means, quite often, a higher speed at the start of laden
passages to control tanks pressure and at the end of ballast passages to use
the operational LNG quantity needed for cargo tank cooling in propulsion
instead of wasting in GCU or condenser steam dump. Charterers are generally
aware of the improved efficiency of this speed pattern.
5.2.7 As part of the speed
optimization process, due account may need to be taken of the need to
coordinate arrival times with the availability of loading/discharge berths,
etc. The number of ships engaged in a particular trade route may need to be
taken into account when considering speed optimization.
5.2.8 A gradual increase
in speed when leaving a port or estuary whilst keeping the engine load within
certain limits may help to reduce fuel consumption.
5.2.9 It is recognized
that under many charter parties the speed of the ships is determined by the
charterer and not the operator. Efforts should be made when agreeing charter
party terms to encourage the ship to operate at optimum speed in order to
maximize energy efficiency.
Optimized shaft power
5.2.10 Operation at constant
shaft RPM can be more efficient than continuously adjusting speed through
engine power. The use of automated engine management systems to control speed
rather than relying on human intervention may be beneficial.
5.2.11 When optimizing shaft
power, due attention should be given to overall power system efficiency. For
example, in some cases reducing load or shaft speed below the minimum necessary
to operate energy recovery systems and shaft generators may increase overall
emissions.