RESOLUTION MEPC.378(80)

(adopted on 7 July 2023)

 

2023 GUIDELINES FOR THE CONTROL AND MANAGEMENT OF SHIPS' BIOFOULING TO MINIMIZE THE TRANSFER OF INVASIVE AQUATIC SPECIES

 

THE MARINE ENVIRONMENT PROTECTION COMMITTEE,

 

RECALLING Article 38 of the Convention on the International Maritime Organization concerning the functions of the Marine Environment Protection Committee relating to any matter within the scope of the Organization concerned with the prevention and control of marine pollution from ships,

 

RECALLING ALSO that Member States of the International Maritime Organization made a clear commitment to minimizing the transfer of invasive aquatic species by shipping in adopting the International Convention for the Control and Management of Ships' Ballast Water and Sediments, 2004,

 

RECALLING FURTHER that studies have shown biofouling on ships to be an important means of transferring invasive aquatic species which, if established in new ecosystems, may pose threats to the environment, human health, property and resources,

 

NOTING the objectives of the Convention on Biological Diversity, 1992, and that the Kunming-Montreal Global Biodiversity Framework includes a target to eliminate, minimize, reduce and/or mitigate the impacts of invasive alien species on biodiversity and ecosystem services by identifying and managing pathways of the introduction of alien species,

 

NOTING ALSO that the transfer and introduction of invasive aquatic species through ships' biofouling threatens the conservation and sustainable use of biological diversity, and implementing practices to control and manage ships' biofouling can greatly assist in reducing the risk of the transfer of invasive aquatic species,

 

NOTING FURTHER that this issue, being of worldwide concern, demands a globally consistent approach to the management of biofouling,

 

RECALLING that, at its sixty-second session, it had adopted, by resolution MEPC.207(62), the 2011 Guidelines for the control and management of ships' biofouling to minimize the transfer of invasive aquatic species (Biofouling Guidelines), developed by the Sub-Committee on Bulk Liquids and Gases,

 

RECALLING ALSO that, at its seventy-second session, it had agreed to review the Biofouling Guidelines, with a view to amending the Guidelines, if required,

 

HAVING CONSIDERED, at its eightieth session, the draft revised Guidelines for the control and management of ships' biofouling to minimize the transfer of invasive aquatic species, developed by the Sub-Committee on Pollution Prevention and Response,

 

1          ADOPTS the 2023 Guidelines for the control and management of ships' biofouling to minimize the transfer of invasive aquatic species, as set out in the annex to the present resolution;

 

2          REQUESTS Member States to take urgent action in applying these Guidelines, including the dissemination thereof to the shipping industry and other interested parties, taking these Guidelines into account when adopting measures to minimize the risk of introducing invasive aquatic species via biofouling, and reporting to MEPC on any experience gained in their implementation;

 

3          AGREES to keep these Guidelines under review in light of the experience gained;

 

4          REVOKES resolution MEPC.207(62).

 

2023 GUIDELINES FOR THE CONTROL AND MANAGEMENT OF SHIPS' BIOFOULING TO MINIMIZE THE TRANSFER OF INVASIVE AQUATIC SPECIES

 

TABLE OF CONTENTS

 

1        INTRODUCTION

 

2        DEFINITIONS

 

3        APPLICATION

 

4        OBJECTIVES

 

5        DESIGN AND CONSTRUCTION

 

6        ANTI-FOULING SYSTEM INSTALLATION AND MAINTENANCE

 Choosing an AFS

 Installing the AFS

 Reinstalling, reapplying or repairing the AFS

 

7        CONTINGENCY ACTION PLANS

 

8        INSPECTION

 Extent of biofouling and recommended actions

 Condition of the AFS

 Inspection report

 

9        CLEANING AND MAINTENANCE

 Procedures for proactive cleaning

 Procedures for reactive cleaning

 Procedures for recycling facilities

 

10      BIOFOULING MANAGEMENT PLAN

 Continuous improvements

 

11      BIOFOULING RECORD BOOK

 

12      DOCUMENTATION AND DISSEMINATION OF INFORMATION

 

13      TRAINING AND EDUCATION

 

14      OTHER MEASURES

 

ABBREVIATIONS

 

APPENDIX 1   ASSESSMENT OF BIOFOULING RISK

 

APPENDIX 2   INSPECTION AND CLEANING REPORTS

 

APPENDIX 3   EXAMPLE FORM OF BIOFOULING MANAGEMENT PLAN

 

APPENDIX 4   EXAMPLE FORM OF BIOFOULING RECORD BOOK

 

1          INTRODUCTION

 

1.1       MEPC 62 adopted the 2011 Guidelines for the control and management of ships' biofouling to minimize the transfer of invasive aquatic species (the Guidelines) through resolution MEPC.207(62). The aim of the Guidelines was to provide a globally consistent approach to managing biofouling by providing useful recommendations of general measures to reduce the risk associated with biofouling for all types of ships.

 

1.2       Member States of the International Maritime Organization (IMO) decided at MEPC 72 to review the Guidelines in order to assess the uptake and effectiveness of the Guidelines and identify any required action.

 

1.3       Studies have shown that biofouling can be a significant vector for the transfer of invasive aquatic species. Biofouling on ships entering the waters of States may result in the establishment of invasive aquatic species, which may pose threats to human, animal and plant life, economic and cultural activities, and the aquatic environment.

 

1.4       Invasive aquatic species have been recognized as one of the major threats for the well-being of the oceans by, inter alia, the Convention on Biological Diversity, several UNEP Regional Seas Conventions, the Asia Pacific Economic Cooperation forum and the Secretariat of the Pacific Region Environmental Programme.

 

1.5       Prediction of risk of introducing invasive species is complex, hence these Guidelines have the intention to minimize the accumulation of biofouling on ships. Biofouling may include invasive species while a clean hull and niche areas significantly reduce this risk. Studies have shown that the biofouling process begins within the first few hours of a ship's immersion in water. The biofouling pressure on a specific ship is influenced by a range of factors, starting with design and construction of the ship hull and niche areas, followed by operating profile of the ship and maintenance history.

 

1.6       These Guidelines describe recommended biofouling management practices, as illustrated in figure 1. Attention during initial ship design and construction may provide effective and sustainable means to reduce ship biofouling risks, supplemented by anti-fouling systems (AFS) for all types of ships' submerged or otherwise wetted surface areas, including hull and niche areas. Although these Guidelines focus on ships using AFS, these biofouling management practices are equally recommended for ships using coatings or surfaces that are not used to control or prevent attachment of organisms, as may be applicable.

 

1.7       The need for inspection and biofouling management may depend on the use of AFS, cleaning regime, and the overall risk of biofouling on the hull and in niche areas. By conducting ship-specific monitoring of risk parameters, identifying potential higher risk for biofouling, an optimized regime for biofouling management can be determined. Cleaning is an important measure to remove biofouling from the hull and niche areas but, when conducted in-water, it poses a risk of releasing invasive aquatic species into the water. Waste substances which are dislodged from the ship during the cleaning operation should therefore be collected. The Guidelines provide guidance for cleaning actions based on a fouling rating number with an overall aim to minimize the risk of transfer of invasive aquatic species. Maintenance and ship recycling should also be conducted with sufficient preventative measures to avoid release of any invasive aquatic species into the water. When conducting biofouling management, potential release of harmful waste substances should also be considered.

 

1.8       In addition to the Biofouling Guidelines, the following frameworks are relevant for minimizing the transfer of invasive aquatic species:

 

.1       the International Convention for the Control and Management of Ships' Ballast Water and Sediments, 2004 (BWM Convention), which aims to minimize the transfer of invasive aquatic species through ships' ballast water and sediments; and

 

.2       the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS Convention), which addresses anti-fouling systems on ships and focuses on the prevention of adverse impacts from the use of anti-fouling systems and the biocides they may contain.

 

1.9       Biofouling management practices may also improve a ship's hydrodynamic performance and can be effective at enhancing energy efficiency and reducing air emissions from ships. This concept has been identified by IMO in the 2022 Guidelines for the development of a ship energy efficiency management plan (SEEMP) (resolution MEPC.346(78)). These Guidelines further support the 2023 IMO Strategy for the reduction of green house gases from ships (resolution MEPC.377(80)).

 

1.10     A GEF-UNDP-IMO GloFouling Partnerships Project was conducted as part of wider efforts by IMO, in collaboration with the United Nations Development Programme (UNDP) and the Global Environment Facility (GEF), to protect marine ecosystems from the negative effects of invasive aquatic species. The aim of the GloFouling Partnerships Project was to build capacity in developing countries for implementing the IMO Biofouling Guidelines and other relevant guidelines to minimize the transboundary introduction of invasive aquatic species, with additional benefits in the reduction of greenhouse gas emissions from global shipping.

 

 

 

 

Figure 1: Simplified flow chart visualizing the biofouling management activities of a ship

 

 

2          DEFINITIONS

 

2.1       For the purposes of these Guidelines, the following definitions apply:

 

Anti-fouling system (AFS) means a coating, paint, surface treatment, surface or device that is used on a ship to control or prevent attachment of organisms.

 

Anti-fouling coating (AFC) means a surface coating or paint designed to prevent, repel or facilitate the detachment of biofouling from hull and niche areas that are typically or occasionally submerged.

 

Biofouling is the accumulation of aquatic organisms such as microorganisms, plants and animals on surfaces and structures immersed in or exposed to the aquatic environment. Biofouling can include pathogens. For microfouling and macrofouling, see definitions below.

 

Biofouling pressure means the biofouling accumulation rate, which differs regionally and seasonally. High biofouling pressure means the development of dense biofouling within a short period of time.

 

Capture is the process of containment, collection and removal of biofouling material and waste substances detached from submerged surfaces during cleaning in water or in dry dock.

 

Cleaning system is the equipment used for, or the process of, removal of biofouling from the ship surface, with or without capture.

 

Dry-dock cleaning refers to the cleaning of the submerged areas when the ship is out of water.

 

Fouling rating is the allocation of a number for a defined inspection area of the ship surface based on a visual assessment, including description of biofouling present and percentage of macrofouling coverage.

 

In-water cleaning is the removal of biofouling from a ship's hull and niche areas while in the water.

 

Invasive aquatic species are non-native species to a particular ecosystem which may pose threats to human, animal and plant life, economic and cultural activities and the aquatic environment.

 

Macrofouling is biofouling caused by the attachment and subsequent growth of visible plants and animals on structures and ships exposed to water. Macrofouling is large, distinct multicellular individual or colonial organisms visible to the human eye such as barnacles, tubeworms, mussels, fronds/filaments of algae, bryozoans, sea squirts and other large attached, encrusting or mobile organisms.

 

Marine growth prevention system (MGPS) is an AFS used for the prevention of biofouling accumulation in niche areas or other surface areas but may also include methods which apply surface treatments.

 

Member States means States that are Members of the International Maritime Organization.

 

Microfouling is biofouling caused by bacteria, fungi, microalgae, protozoans and other microscopic organisms that creates a biofilm also called a slime layer.

 

Niche areas are a subset of the submerged surface areas on a ship that may be more susceptible to biofouling than the main hull owing to structural complexity, different or variable hydrodynamic forces, susceptibility to AFC wear or damage, or inadequate or no protection by AFS.

 

Organization means the International Maritime Organization.

 

Port State authority means any official or organization authorized by the Government of a port State to verify the compliance and enforcement of standards and regulations relevant to the implementation of national and international shipping control measures.

 

Proactive cleaning is the periodic removal of microfouling on ships' hulls to prevent or minimize attachment of macrofouling.

 

Reactive cleaning is a corrective action during which biofouling is removed from a ship's hull and niche areas either in water with capture or in dry dock.

 

Ship means a vessel of any type whatsoever operating in the aquatic environment and includes hydrofoil boats, air-cushion vehicles, submersibles, floating craft, fixed or floating platforms, floating storage units and floating production storage and off-loading units.

 

States means coastal, port, flag or Member States, as appropriate.

 

Waste substances are dissolved and particulate materials that may be released or produced during cleaning or maintenance, and may include biocides, metals, organic substances, removed biofouling, pigments, microplastics or other contaminants that could have a negative impact on the environment.

 

3          APPLICATION

 

3.1       The Guidelines are intended to provide useful recommendations for measures to minimize biofouling for all types of ships. The Guidelines are directed at various stakeholders, such as ship designers, shipbuilders, anti-fouling paint manufacturers and suppliers, States, including environmental and regulatory agencies, classification societies, shipowners, ship operators, charterers, shipmasters, port authorities, ship cleaning and maintenance operators, inspection organizations, ship repair, dry-docking and recycling facilities, and any other interested parties.

 

3.2       Alternative procedures, methods or actions taken to meet the objectives of these Guidelines which are not described should be reported to the Organization by Members of the Organization and their representatives and be taken into account in future reviews of the Guidelines as appropriate.

 

3.3       A separate guidance document, based on these Guidelines, provides advice relevant to owners and/or operators of recreational craft less than 24 metres in length, using terminology appropriate for that sector (Guidance for minimizing the transfer of invasive aquatic species as biofouling (hull fouling) for recreational craft (MEPC.1/Circ.792)).

 

3.4       The Guidelines may not be relevant to ships which operate only in the same waters in which the biofouling was accumulated. Although operation in the same waters leads to no risk of introducing invasive aquatic species, measures to avoid discharge of harmful waste substances during cleaning may still be relevant.

 

3.5       An inspection regime as defined in paragraphs 8.4 to 8.6 may not be relevant to a ship when idle for a longer period. To maintain the anti-fouling effect of an AFS, inspection and reactive cleaning may be needed before the ship is reactivated to reduce the risk of biofouling.

 

4          OBJECTIVES

 

4.1       The objective of these Guidelines is to minimize the transfer of invasive aquatic species through biofouling on ships.

 

4.2       Procedures, methods and actions taken in line with these Guidelines should safeguard the obligation under the United Nations Convention on the Law of the Sea (UNCLOS), article 194, to prevent, reduce and control pollution of the marine environment. This includes ensuring not to transfer, directly or indirectly, damage or hazards from one area to another, or transform one type of pollution into another (ref. UNCLOS article 195), as well as preventing the intentional or accidental introduction of species, alien or new, to a particular part of the marine environment (ref. UNCLOS article 196).

 

4.3       The objective of these Guidelines is pursued by providing a globally consistent approach to stakeholders on the control and management of biofouling, which will contribute to minimizing the risk of transferring invasive aquatic species from biofouling on ships. An additional effect of good biofouling management can be a reduction in emissions to air from ships, due to lower fuel demand in operation as a result of a clean hull.

 

5          DESIGN AND CONSTRUCTION

 

5.1       Initial ship design and construction offers the most comprehensive, effective and long-lasting means to minimize ship biofouling risks. In the design and construction of a ship, or when a ship is being significantly modified, the following items, not exhaustive, should be taken into consideration:

 

.1       small niches and sheltered areas should be avoided as far as practical, e.g. flush mounting pipes in sea chests (where not practical, these should be designed so that they may be easily accessed for inspection, cleaning and application of AFS like marine growth prevention systems (MGPS));

 

.2       rounding and/or bevelling of corners, gratings and protrusions to promote more effective coverage of AFC and hinging of gratings to enable diver access;

 

.3       providing the capacity to block off the sea chest and other areas, such as moon pools, floodable docks and other free-flood spaces, for cleaning and treatment, if applicable and appropriate; and

 

.4       internal seawater cooling systems should be designed with a minimum number of bends and flanges. The design should be made of appropriate material to minimize biofouling, and be compatible with MGPS, if any. Dead ends, as can be found between different systems like cross-over piping between cooling and general service systems, should be avoided. Standby pumps and piping should be fully integrated into the systems to avoid stagnant water.

 

6          ANTI-FOULING SYSTEM INSTALLATION AND MAINTENANCE

 

6.1       AFS are effective means to minimize biofouling on ships' submerged surfaces, including the hull and niche areas.

 

6.2       Restrictions on the use of certain substances in the AFC are regulated by the AFS Convention.

 

Choosing an AFS

 

6.3       It is recommended to install AFS in all submerged surfaces on a ship where biofouling may attach. Various AFS are designed for different ship operating profiles, some suitable for hull and some for niche areas and therefore will require different maintenance activities. Thus, it is essential that shipowners, ship operators and shipbuilders obtain appropriate technical advice. AFS manufacturers are best suited to provide advice to ensure a suitable system is applied, reapplied, installed or renewed. As biofouling may typically be found at higher abundance in niche areas, where flow characteristics change as the ship moves through the water, it is recommended to choose a combination of AFC and MGPS, suitable for different submerged areas. If an appropriate AFS is not applied, biofouling accumulation may increase, and more frequent inspections may be necessary. Some factors to consider when choosing an AFS include the following:

 

.1       Ship design and construction: Where possible and appropriate upon the recommendation of AFS manufacturers, targeted installation of AFS may be employed for different areas of the ship. AFS for the hull may include specific AFC, paint and/or surface treatment. Installation of any proactive cleaning measures should be in accordance with the recommendations from the AFC provider and should not damage the AFC. Different AFS are designed to optimize their performance for specific ship speeds. For niche areas, the selected AFS should be optimized for conditions of the niche area, e.g. an AFC may be recommended for use in combination with effective MGPS to minimize biofouling. AFC selection should be based on expected wear, abrasion and water flow rates.

 

.2       Active ingredients of AFC: Environmental impact assessment of the selected AFC with respect to the release of harmful substances should be considered. The limitations of an AFC to minimize biofouling should be known and may include operating profile, aquatic environment, ship design and life cycle of AFC. Decision makers should be aware of the limitations of each AFC and the recommended in-water cleaning methods in order to minimize potential environmental impacts and damage to the system. Depending on the type of AFC, various types of waste substances may be released when cleaning. Some waste substances may easily be captured but others are fine particles or dissolved substances that may be released into the water. Therefore, not all AFC types are designed for frequent cleaning. The AFC manufacturers should provide key information on any biocides used and coating types on publicly available safety and technical datasheets. Frequent cleaning may impact the effectiveness of a specific AFC, and it is therefore recommended that the AFC manufacturers provide relevant guidance. In-water cleaning service providers and manufacturers of cleaning methods/equipment should provide guidance considering compatibility with AFC type.

 

.3       Operating profile: Patterns of use, operating routes, ship activity levels and periods of inactivity may influence the rate of biofouling accumulation and thus the effectiveness of the AFS. Inactivity may cause higher accumulation of biofouling. Biofouling may attach more easily on slow-moving ships.

 

.4       Aquatic environment: Biofouling pressure differs between areas, depending on temperature, salinity and nutrient conditions. Biofouling grows more slowly, but is not prevented, in low temperature waters. Ships operating in ice conditions should consider special AFC. Different organisms grow in different salinity waters and, if a ship operates in all salinity ranges, the anti-fouling system should target a wide range of organisms causing fouling. The benthic (seabed) environment should also be considered. Increasing depth of water and distance from shore may decrease susceptibility for biofouling. Additionally, higher content of nutrients in the water may increase algal blooms and susceptibility to biofouling.

 

.5       Cleaning method: Although cleaning system manufacturers are encouraged to find technological solutions that allow them to clean a wide variety of AFC, not all AFC can be cleaned by every cleaning system. When selecting the AFC, the available cleaning technologies and techniques and their suitability for the specific AFC should be considered. Therefore, AFC manufacturers should provide key information on any biocides used and coating types. The choice of AFC should be compatible with the cleaning technologies available to ensure both minimum biofouling growth as well as reducing the risk of damage to the AFC and the potential release of harmful waste substances to the environment.

 

.6       Maintenance: The lifespan of an AFS should be considered in combination with dry-docking schedules. AFC lifespan and lifetime of MGPS (e.g. anodes) should exceed the period between dry-dockings.

 

.7       Legal requirements: In addition to the AFS Convention, any national or regional regulatory requirements, if relevant, should be considered in the selection of AFS. This may apply to release of chemicals from MGPS and the AFS.

 

Installing the AFS

 

6.4       Installing an AFS in hull and niche areas should be in accordance with the manufacturer's guidance.

 

6.5       Niche areas are particularly susceptible to biofouling growth. Care should be taken in surface preparation and application of any AFC to ensure adequate adhesion and coating thickness. Particular attention should be paid to corners, edges, pipes, holding brackets and bars of gratings. Corners, edges and welded joints should be smooth and coated with adequate coating thickness to optimize system effectiveness. Additionally, for such areas, it is recommended to apply a touch up to ensure film thickness or a higher-grade AFC.

 

6.6       A non-exhaustive list of recommended measures for installation of an AFS in niche areas is as follows:

 

.1       Sea chest: Internal surfaces and inlet gratings of sea chests should be protected by an AFS that is suitable for the flow conditions of the area over the gratings and through the sea chest.

 

.2       Bow and stern thrusters: Free-flooding spaces which may exist around the thruster tunnel require special attention. The housings/recesses and retractable fittings such as stabilizers and thruster bodies should have an AFC of adequate thickness for optimal effectiveness.

 

.3       Rudder hinges and stabilizer fin apertures: Rudders and stabilizer fins should be moved through their full range of motion during the coating process to ensure that all surfaces are correctly coated to the specification of the AFC. Rudders, rudder fittings and the hull areas around them should also be adequately coated to withstand the increased wear rates experienced in these areas.

 

.4       Propeller and shaft: Propellers and immersed propeller shafts are generally not coated but polished. Fouling release coatings or other suitable coatings may be applied where possible and appropriate to maintain efficiency.